Rainbow-electronics ATmega162V Manuale Utente Pagina 181
- Pagina / 323
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
181
ATmega162/V
2513E–AVR–09/03
The recommendations of the maximum receiver baud rate error was made under the
assumption that the Receiver and Transmitter equally divides the maximum total error.
There are two possible sources for the receivers baud rate error. The receiver’s system
clock (XTAL) will always have some minor instability over the supply voltage range and
the temperature range. When using a crystal to generate the system clock, this is rarely
a problem, but for a resonator the system clock may differ more than 2% depending of
the resonators tolerance. The second source for the error is more controllable. The baud
rate generator can not always do an exact division of the system frequency to get the
baud rate wanted. In this case an UBRR value that gives an acceptable low error can be
used if possible.
Multi-processor
Communication Mode
Setting the Multi-processor Communication mode (MPCM) bit in UCSRA enables a fil-
tering function of incoming frames received by the USART Receiver. Frames that do not
contain address information will be ignored and not put into the receive buffer. This
effectively reduces the number of incoming frames that has to be handled by the CPU,
in a system with multiple MCUs that communicate via the same serial bus. The Trans-
mitter is unaffected by the MPCM setting, but has to be used differently when it is a part
of a system utilizing the Multi-processor Communication mode.
If the receiver is set up to receive frames that contain 5 to 8 data bits, then the first stop
bit indicates if the frame contains data or address information. If the receiver is set up for
frames with nine data bits, then the ninth bit (RXB8) is used for identifying address and
data frames. When the frame type bit (the first stop or the ninth bit) is one, the frame
contains an address. When the frame type bit is zero the frame is a data frame.
Table 71. Recommended Maximum Receiver Baud Rate Error for Normal Speed Mode
(U2X = 0)
D
# (Data+Parity Bit) R
slow
(%) R
fast
(%) Max. Total Error (%)
Recommended Max.
Receiver Error (%)
5 93.20 106.67 +6.67/-6.8% ± 3.0
6 94.12 105.79 +5.79/-5.88 ± 2.5
7 94.81 105.11 +5.11/-5.19 ± 2.0
8 95.36 104.58 +4.58/-4.54 ± 2.0
9 95.81 104.14 +4.14/-4.19 ± 1.5
10 96.17 103.78 +3.7 /-3.83 ± 1.5
Table 72. Recommended Maximum Receiver Baud Rate Error for Double Speed Mode
(U2X = 1)
D
# (Data+Parity Bit) R
slow
(%) R
fast
(%) Max. Total Error (%)
Recommended Max.
Receiver Error (%)
5 94.12 105.66 +5.66/-5.88 ± 2.5
6 94.92 104.92 +4.92/-5.08 ± 2.0
7 95.52 104.35 +4.35/-4.48 ± 1.5
8 96.00 103.90 +3.90/-4.00 ± 1.5
9 96.39 103.53 +3.53/-3.61 ± 1.5
10 96.70 103.23 +3.23/-3.30 ± 1.0
- Features 1
- ATmega162/V 10
- Ports as General Digital 63
- INSTRUCTIONS 64
- SYNC LATCH 64
- SYSTEM CLK 64
- 2513E–AVR–09/03 65
- DATA BUS 67
- Regional Headquarters 323
Prodotti e manuali riguardandi Sensori Rainbow-electronics ATmega162V
Sensori Rainbow-electronics AT73C246 Manuale Utente
(159 pagine)
(159 pagine)
Electrolux ESL66075R Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Electrolux ESL66075R.
Wir stellen 1 PDF-Handbücher Electrolux ESL66075R zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commenti su questo manuale