Rainbow-electronics DS1855 Manuale Utente

Navigare online o scaricare Manuale Utente per Hardware del computer Rainbow-electronics DS1855. Rainbow Electronics DS1855 User Manual Manuale Utente

  • Scaricare
  • Aggiungi ai miei manuali
  • Stampa
  • Pagina
    / 20
  • Indice
  • SEGNALIBRI
  • Valutato. / 5. Basato su recensioni clienti
Vedere la pagina 0
1 of 20 100101
FEATURES
§ Two linear taper potentiometers
- DS1855-010 (one 10k, 100 position and
one 10k, 256 position)
- DS1855-020 (one 10k, 100 position and
one 20k, 256 position)
- DS1855-050 (one 10k, 100 position and
one 50k, 256 position)
- DS1855-100 (one 10k, 100 position and
one 100k, 256 position)
§ 256 bytes of EEPROM memory
§ Access to data and potentiometer control via
a 2-wire interface
§ External write-protect pin to protect data and
potentiometer settings
§ Data and potentiometer settings also can be
write-protected through software control
§ Nonvolatile wiper storage
§ Operates from 3V or 5V supplies
§ Packaging: 14-pin TSSOP, 16-ball STPBGA,
flip-chip package
§ Industrial operating temperature:
-40ºC to +85ºC
§ Programming temperature: 0ºC to +85ºC
DESCRIPTION
The DS1855 dual nonvolatile (NV) digital potentiometer and secure memory consists of one 100-position
linear taper potentiometer, one 256-position linear taper potentiometer, 256 bytes of EEPROM memory,
and a 2-wire interface. The DS1855, which features a new software write protect, is an upgrade of the
DS1845. The DS1855 provides an ideal method for setting bias voltages and currents in control
applications using a minimum of circuitry. The EEPROM memory allows a user to store configuration or
calibration data for a specific system or device as well as provide control of the potentiometer wiper
settings. Any type of user information may reside in the first 248 bytes of this memory. The next two
addresses of EEPROM memory are for potentiometer settings and the remaining 6 bytes of memory are
reserved. These reserved and potentiometer registers should not be used for data storage. Access to this
EEPROM is via an industry-standard 2-wire bus. The interface I/O pins consist of SDA and SCL. The
wiper position of the DS1855, as well as EEPROM data, can be write-protected through hardware using
the write-protect input pin (WP) or software using the 2-wire interface.
DS1855
Dual Nonvolatile Digital Potentiomete
r
and Secure Memor
y
www.maxim-ic.com
SDA 1 14 Vcc
SCL 2
13
H0
A0
3
12
W1
A1 4 11 H1
A2 5
10
L1
WP 6 9 W0
GND
78
L0
14-Pin TSSOP (173-mil)
A
B
C
D
1 2 3 4
Top View
16-Ball STPBGA (4mm x 4mm)
14-Pin Flip Chip (100-mil x 100-mil)
(Not Shown)
Vedere la pagina 0
1 2 3 4 5 6 ... 19 20

Sommario

Pagina 1 - (Not Shown)

1 of 20 100101FEATURES§ Two linear taper potentiometers- DS1855-010 (one 10k, 100 position andone 10k, 256 position)- DS1855-020 (one 10k, 100 posi

Pagina 2 - PIN DESCRIPTIONS

DS185510 of 20LOCKING AND UNLOCKING EEPROMIn addition to the WP pin, it is possible to write-protect, or lock, certain portions of the EEPROM throughs

Pagina 3 - DS1855 BLOCK DIAGRAM Figure 1

DS185511 of 202-WIRE PROTOCOL DATA TRANSFER PROTOCOL Figure 22-WIRE AC CHARACTERISTICS Figure 3

Pagina 4 - MEMORY ORGANIZATION

DS185512 of 20ABSOLUTE MAXIMUM RATINGS*Voltage on Any Pin Relative to Ground -0.3V to +6.0VOperating Temperature Range -40°C to +85°C; Extended Indust

Pagina 5

DS185513 of 20ANALOG RESISTOR CHARACTERISTICS (-40°C to +85°C; VCC = 2.7V to 5.5V)PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTESResistor Inputs L

Pagina 6 - 2-WIRE OPERATION

DS185514 of 20AC ELECTRICAL CHARACTERISTICS (-40°C to +85°C, VCC = 2.7V to 5.5V)PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTESSCL Clock Frequency

Pagina 7 - SEQUENTIAL ADDRESS READ

DS185515 of 20NOTES:1. All voltages are referenced to ground.2. ISTBY specified with for VCC = 3.0V and 5.0V, and control port logic pins are driven

Pagina 8 - 2-WIRE SERIAL PORT OPERATION

DS185516 of 20TYPICAL OPERATING CHARACTERISTICS(VCC = 5V, T = +25ºC, unless otherwise specified)WIPER RESISTANCE (W)SUPPLY CURRENT (mA)SUPPLY CURRENT

Pagina 9 - WRITE PROTECT

DS185517 of 20TYPICAL OPERATING CHARACTERISTICS (cont.)(VCC = 5V, T = +25ºC, unless otherwise specified)ATTENUATION (dB)END-TO-END RESISTANCE CHANGE (

Pagina 10 - LOCKING AND UNLOCKING EEPROM

DS185518 of 20TYPICAL OPERATING CHARACTERISTICS (cont.)(VCC = 5V, T = +25ºC, unless otherwise specified)SUPPLY CURRENT (mA)ACTIVE SUPPLY CURRENT vs. F

Pagina 11 - 11 of 20

DS185519 of 20TYPICAL OPERATING CHARACTERISTICS (cont.)(VCC = 5V, T = +25ºC, unless otherwise specified)RESISTANCE vs. VOLTAGE (POWER-DOWN)010,00020,0

Pagina 12 - = 2.7V to 5.5V)

DS18552 of 20PIN DESCRIPTIONSName TSSOP BGA DescriptionVCC14 A3 Power Supply Terminal. The DS1855 will support supplyvoltages ranging f

Pagina 13 - = 2.7V to 5.5V)

DS185520 of 20ORDERING INFORMATIONORDERINGNUMBERPACKAGE OPERATINGTEMPERATUREVERSIONPot 0/Pot 1DS1855E-010 14-PIN TSSOP (173-MIL) -40ºC TO +85ºC10kW/10

Pagina 14

DS18553 of 20DS1855 BLOCK DIAGRAM Figure 1Up to eight DS1855s can be installed on a single 2-wire bus. Access to an individual device is achievedby us

Pagina 15 - 15 of 20

DS18554 of 20MEMORY ORGANIZATIONThe DS1855’s serial EEPROM is internally organized with 256 words of 1 byte each. Each word requiresan 8-bit address f

Pagina 16 - VOLTAGE (V)

DS18555 of 20FBh – FCh Lock Bytes Writing to these two bytes allows the user to lock or unlock thememory described in byte FAh.LOCK: If memory locatio

Pagina 17 - FREQUENCY (Hz)

DS18556 of 202-WIRE OPERATIONClock and Data TransitionsThe SDA pin is normally pulled high with an external resistor or device. Data on the SDA pin ma

Pagina 18 - FREQUENCY (kHz)

DS18557 of 20The DS1855 is capable of an 8-byte page write. A page write is initiated the same way as a byte write, butthe master does not send a STOP

Pagina 19 - RESISTANCE FROM W TO L

DS18558 of 202-WIRE SERIAL PORT OPERATIONThe 2-wire serial port interface supports a bidirectional data transmission protocol with deviceaddressing. A

Pagina 20 - ORDERING INFORMATION

DS18559 of 201. Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the master isthe command/control byte. Nex

Commenti su questo manuale

Nessun commento